Straton Group
Straton Group
Chennai, Tamil Nadu
Send SMS
Send E-mail

PVC Boards

Our latest innovative introduction in the market replacing traditional plywood/boards: PVC integral foam sheet are chemically foamed, extruded rigid, light weight sheet with fine & homogeneous closed cell structure & smooth, hard surface finish on both sides. PVCdoes not corrode and are highly resistant to rot, decay, and Marine Borer attack and are often considered a sustainable material because they can be made using recycled plastics and the waste products of the

...

Read more

Get CALLBACK

PVC Celuka Foam Boards

PVC Celuka Foam Boards
 
Get Best Quote
Approx Price: Rs 117 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
BrandEuro
SizeCustomized
ThicknessCustomized

PVC celuka Foam Boards can be easily machined using ordinary tools used for processing metal or wood. However, the following precautions need to be taken. Avoid sharp edges and deep notches which can cause stresses leading to early breakage to the plastic sheets. Cooling is not necessary under normal conditions if the cutting edges are kept sharp and the processing heat is dissipated by quickly removing the shavings. However, compressed air, water or cooling liquid is suitable if used in accordance with the existing safety instructions. To obtain smooth or glossy surfaces on the PVC boards, finishing with felt buffing wheels or tapes is recommended.
  • Cutting/Sawing – PVC sheets up to 3mm thickness can be cut with a knife or blade. Thicker PVC sheets can be cut with hand saw or circular saw. High saw speeds up to 3000 RPM with tooth pitch of 5 to 10mm are used depending on sheet thickness. For circular saws, it is commonly recommended to use tooth geometry alternating between flat tooth, trapezoidal tooth and rigid metal. Always fasten the sheet and avoid vibrations during cutting to achieve clean cutting edges.
  • Drilling – PVC sheets can be drilled with conventional, high helix, high speed steel carbide tipped metal bits. Cutting edges must be kept sharp to prevent poor surface finish and undersized holes. Cutting and feeding speed depends on depth of bores, the thicker the sheet the lower the speed.
  • Routing – Stationary or hand routers can be used for slotting, beveling, rabbeting, rounding edges and trimming to the PVC boards. Best cutting results are obtained with carbide tipped router bits.
  • Milling – PVC sheets can be milled with milling tool that has allowance to accommodate smoother removal of chips. High forward feed along with moderate cutting speed and deep cuts will lead to good results.
  • Turning – PVC sheets can be worked by turning with a point of turning tool rounded to 0.50 mm radius to avoid linear marks on cutting surfaces. During precision turning, lower cut (2mm) and faster feeding should be used to prevent sheet breakage.
  • Cutting Punching – PVC sheets can be easily cut by shearing up to 3mm thickness. In case any deformity, rougher cut surface or fracturing is noticed, it is primarily because of sheet temperature. PVC sheet, a thermoplastic material, tends to acquire brittleness at lower temperatures. Therefore, pre-heat the sheet material to 95° – 131° F, before shearing. Die cutting by “Steel rule dies” is a common practice. Ideally it is 25mm wide strip steel, thickness 0.35–1mm, with one edge pre-shaped as knife. Bevel may be used depending on cut requirements with one side or both side honing. The bevel should be 5 or 6mm in length.
Yes! I am interested
Watch Video
Get CALLBACK

PVC Boards

PVC Boards
 
Get Best Quote
Approx Price: Rs 114 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
BrandEuro
ColorWhite
SizeCustomized

Our PVC Boards possesses such physical properties that provide designers with an array of options while designing new products and developing solutions as it also acts as a replacement or refurbishment material. It is an upward trend for PVC foam board suppliers in India as the customers using plywood boards are now switching preference. On the contrary, PVC boards are lighter, less operative-expensive and offer many performance advantages. PVC panels are easy to install, water-proof, maintenance-free and are available in various textures, patter and design.
Features:


  • Excellent finishing
  • Optimum strength
  • Good impact resistance

Specifications:


  • straton
  • Width: 4
  • Length: 8
  • Thickness: 8, 10, 12, 15, 18, 24 & 30
  • Other Specs: Variant colors - Red, Blue, Orange, Yellow, White and dark brown
Yes! I am interested
Watch Video
Get CALLBACK

PVC Panel Boards

PVC Panel Boards
 
Get Best Quote
Approx Price: Rs 57 / Square Feet

Product Details:
Minimum Order Quantity500 Square Feet
Body MaterialPVC
ColorWhite, Multicolor
DesignStandard
Packing TypeBox
TypePVC Board

We are redically substituting BWP Plywood, MDF/HDF, Chip/Particle Board etc.

Features:

Maintenance Free-
A virtuous Cap-Ex resulting in a lower Op-Ex in long term

Enhanced Efficiency- Saves Labour time in machinability

Assists in enhancing the projects LEED/equivalent green building ratings

Ease in logistics and handling-
Low volume to mass ratio

Absolute density measure- Homogenous in nature

Application specific- Can be used as a structural as well as an asthetic finishing product.
Yes! I am interested
Get CALLBACK

PVC Plastic Boards

PVC Plastic Boards
 
Get Best Quote
Approx Price: Rs 114 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
BrandEuro
ColorMulticolor
SizeCustomized

Our PVC Boards possesses such physical properties that provide designers with an array of options while designing new products and developing solutions as it also acts as a replacement or refurbishment material. It is an upward trend for PVC foam board suppliers in India as the customers using plywood boards are now switching preference.
Yes! I am interested
Watch Video
Get CALLBACK

PVC Wardrobes & Kitchen Cabinet

PVC Wardrobes & Kitchen Cabinet
 
Get Best Quote
Approx Price: Rs 117 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
MirrorYes
ShapeCustomized
SizeCustomized

Our Latest innovative introduction in the market supplanting traditional plywoods/boards in their uses and much beyond: Straton PVC Integral foam boards are chemically foamed, extruded rigid, light weight sheets with fine and homogenous closed cell structure and smooth finishes on both sides.
Yes! I am interested
View PDF Watch Video
Get CALLBACK

PVC Partition Systems

PVC Partition Systems
 
Get Best Quote
Approx Price: Rs 166 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
ShapeCustomized
SizeCustomized
BrandEuro

Our PVC Boards possesses such physical properties that provide designers with an array of options while designing new products and developing solutions as it also acts as a replacement or refurbishment material. It is an upward trend for PVC foam board suppliers in India as the customers using plywood boards are now switching preference. On the contrary, PVC boards are lighter, less operative-expensive and offer many performance advantages. PVC panels are easy to install, water-proof, maintenance-free and are available in various textures, patter and design.
Yes! I am interested
View PDF Watch Video
Get CALLBACK

PVC Door

PVC Door
 
Get Best Quote
Approx Price: Rs 215 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
BrandStraton Composite
ColorWhite
ConditionNew
Density600 Kg/m3
DesignStandard
Dimension/SizeCustomized
FinishPlain
Length81''
PositionInterior
StyleHalf Height

PVC sheets can be drilled with conventional, high helix, high speed steel carbide tipped metal bits. Cutting edges must be kept sharp to prevent poor surface finish and undersized holes. Cutting and feeding speed depends on depth of bores, the thicker the sheet the lower the speed. Stationary or hand routers can be used for slotting, beveling, rabbeting, rounding edges and trimming to the PVC boards. Best cutting results are obtained with carbide tipped router bits.PVC sheets can be easily cut by shearing up to 3mm thickness. In case any deformity, rougher cut surface or fracturing is noticed, it is primarily because of sheet temperature. PVC sheet, a thermoplastic material, tends to acquire brittleness at lower temperatures. Therefore, pre-heat the sheet material to 95° – 131° F, before shearing. Die cutting by “Steel rule dies” is a common practice. Ideally it is 25mm wide strip steel, thickness 0.35–1mm, with one edge pre-shaped as knife. Bevel may be used depending on cut requirements with one side or both side honing. The bevel should be 5 or 6mm in length.
Yes! I am interested
View PDF Watch Video
Get CALLBACK

PVC Work Stations

PVC Work Stations
 
Get Best Quote
Approx Price: Rs 117 / Square Feet

Product Details:
Minimum Order Quantity500 Square Feet
BrandStraton
ColorWhite
Design TypeStandard
Size8' X 4'

PVC Sheet can be bonded both to itself and other materials. Adhesive types must be chosen according to bonding requirements.
  • Edge bonding and joining parts of sheet materials: PVC solvents such as Tetrahydrofuran, Methyl Ethyl Ketone or Cyclohexanone can be used. Solvents must be fresh and effective.
  • Bonding to nonporous materials such as other plastics/metals: Polyurethane or other synthetic rubber based adhesives are recommended. Solvent-free two part. Polyurethane adhesive can also be used. Adhesives must be applied to both faces; quantity approximately 150g/m_. A parallel bead of adhesive is often preferred because it offers evaporation of solvent providing faster cure.
  • Bonding with flexible PVC sheets: Only plasticizer-resistant type adhesives should be used. Bonding porous material such as, papers, Textiles, Fabrics or
  • Wood: Contact adhesive with solvent can be used. Follow same directions for application as for non-porous bonding. Pressure sensitive tape can be used for stress free and less demanding applications.
Yes! I am interested
Watch Video
Get CALLBACK

PVC Foam Board

PVC Foam Board
 
Get Best Quote
Approx Price: Rs 117 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
BrandStraton
ColorWhite
MaterialPVC Foam
Size8' X 4'
Thickness15mm

PVC sheets are easy to paint with rigid PVC compatible paints. These can be Vinyl, Acrylic lacquers, or two part Polyurethane based paints. Sheets must be dry, clean and oil/grease free. Cloth soaked in Isopropyl alcohol is recommended for surface cleaning.
Yes! I am interested
Watch Video
Get CALLBACK

PVC Plyboard

PVC Plyboard
 
Get Best Quote
Approx Price: Rs 114 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
ColorWhite
Length8 feet
Thickness18mm
Width4 feet

Our latest innovative introduction in the market replacing traditional plywoods/boards: Straton PVC Integral Free Foam Sheet are chemically foamed, extruded rigid, light weight sheet with fine homogeneous closed cell structure smooth, hard surface finish on both sides.
Yes! I am interested
Watch Video
Get CALLBACK

PVC Celuka Boards

PVC Celuka Boards
 
Get Best Quote
Approx Price: Rs 117 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
BrandStraton
ColorWhite
Size8' X 4'

PVC celuka boards can be easily machined using ordinary tools used for processing metal or wood. However, the following precautions need to be taken. Avoid sharp edges and deep notches which can cause stresses leading to early breakage to the plastic sheets. Cooling is not necessary under normal conditions if the cutting edges are kept sharp and the processing heat is dissipated by quickly removing the shavings. However, compressed air, water or cooling liquid is suitable if used in accordance with the existing safety instructions. To obtain smooth or glossy surfaces on the PVC boards, finishing with felt buffing wheels or tapes is recommended.
  • Cutting/Sawing – PVC sheets up to 3mm thickness can be cut with a knife or blade. Thicker PVC sheets can be cut with hand saw or circular saw. High saw speeds up to 3000 RPM with tooth pitch of 5 to 10mm are used depending on sheet thickness. For circular saws, it is commonly recommended to use tooth geometry alternating between flat tooth, trapezoidal tooth and rigid metal. Always fasten the sheet and avoid vibrations during cutting to achieve clean cutting edges.
  • Drilling – PVC sheets can be drilled with conventional, high helix, high speed steel carbide tipped metal bits. Cutting edges must be kept sharp to prevent poor surface finish and undersized holes. Cutting and feeding speed depends on depth of bores, the thicker the sheet the lower the speed.
  • Routing – Stationary or hand routers can be used for slotting, beveling, rabbeting, rounding edges and trimming to the PVC boards. Best cutting results are obtained with carbide tipped router bits.
  • Milling – PVC sheets can be milled with milling tool that has allowance to accommodate smoother removal of chips. High forward feed along with moderate cutting speed and deep cuts will lead to good results.
  • Turning – PVC sheets can be worked by turning with a point of turning tool rounded to 0.50 mm radius to avoid linear marks on cutting surfaces. During precision turning, lower cut (2mm) and faster feeding should be used to prevent sheet breakage.
  • Cutting Punching – PVC sheets can be easily cut by shearing up to 3mm thickness. In case any deformity, rougher cut surface or fracturing is noticed, it is primarily because of sheet temperature. PVC sheet, a thermoplastic material, tends to acquire brittleness at lower temperatures. Therefore, pre-heat the sheet material to 95° – 131° F, before shearing. Die cutting by “Steel rule dies” is a common practice. Ideally it is 25mm wide strip steel, thickness 0.35–1mm, with one edge pre-shaped as knife. Bevel may be used depending on cut requirements with one side or both side honing. The bevel should be 5 or 6mm in length.
Yes! I am interested
Watch Video
Get CALLBACK

PVC Celuka Sheets

PVC Celuka Sheets
 
Get Best Quote
Approx Price: Rs 114 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
ColorWhite
FeaturesFire Retardant, Moisture Resistant, Water proof
Size(FeetXFeet)8' X 4'
Thickness(mm)6

PVC celuka sheets can be easily machined using ordinary tools used for processing metal or wood. However, the following precautions need to be taken. Avoid sharp edges and deep notches which can cause stresses leading to early breakage to the plastic sheets. Cooling is not necessary under normal conditions if the cutting edges are kept sharp and the processing heat is dissipated by quickly removing the shavings. However, compressed air, water or cooling liquid is suitable if used in accordance with the existing safety instructions. To obtain smooth or glossy surfaces on the PVC boards, finishing with felt buffing wheels or tapes is recommended.
  • Cutting/Sawing – PVC sheets up to 3mm thickness can be cut with a knife or blade. Thicker PVC sheets can be cut with hand saw or circular saw. High saw speeds up to 3000 RPM with tooth pitch of 5 to 10mm are used depending on sheet thickness. For circular saws, it is commonly recommended to use tooth geometry alternating between flat tooth, trapezoidal tooth and rigid metal. Always fasten the sheet and avoid vibrations during cutting to achieve clean cutting edges.
  • Drilling – PVC sheets can be drilled with conventional, high helix, high speed steel carbide tipped metal bits. Cutting edges must be kept sharp to prevent poor surface finish and undersized holes. Cutting and feeding speed depends on depth of bores, the thicker the sheet the lower the speed.
  • Routing – Stationary or hand routers can be used for slotting, beveling, rabbeting, rounding edges and trimming to the PVC boards. Best cutting results are obtained with carbide tipped router bits.
  • Milling – PVC sheets can be milled with milling tool that has allowance to accommodate smoother removal of chips. High forward feed along with moderate cutting speed and deep cuts will lead to good results.
  • Turning – PVC sheets can be worked by turning with a point of turning tool rounded to 0.50 mm radius to avoid linear marks on cutting surfaces. During precision turning, lower cut (2mm) and faster feeding should be used to prevent sheet breakage.
  • Cutting Punching – PVC sheets can be easily cut by shearing up to 3mm thickness. In case any deformity, rougher cut surface or fracturing is noticed, it is primarily because of sheet temperature. PVC sheet, a thermoplastic material, tends to acquire brittleness at lower temperatures. Therefore, pre-heat the sheet material to 95° – 131° F, before shearing. Die cutting by “Steel rule dies” is a common practice. Ideally it is 25mm wide strip steel, thickness 0.35–1mm, with one edge pre-shaped as knife. Bevel may be used depending on cut requirements with one side or both side honing. The bevel should be 5 or 6mm in length.
Yes! I am interested
View PDF Watch Video
Get CALLBACK

PVC Decking

PVC Decking
 
Get Best Quote
Approx Price: Rs 114 / Square Feet

Product Details:
Minimum Order Quantity160 Square Feet
BrandStraton
ColorWhite
Length8'
Width4'

PVC celuka boards can be easily machined using ordinary tools used for processing metal or wood. However, the following precautions need to be taken. Avoid sharp edges and deep notches which can cause stresses leading to early breakage to the plastic sheets. Cooling is not necessary under normal conditions if the cutting edges are kept sharp and the processing heat is dissipated by quickly removing the shavings. However, compressed air, water or cooling liquid is suitable if used in accordance with the existing safety instructions. To obtain smooth or glossy surfaces on the PVC boards, finishing with felt buffing wheels or tapes is recommended.
  • Cutting/Sawing – PVC sheets up to 3mm thickness can be cut with a knife or blade. Thicker PVC sheets can be cut with hand saw or circular saw. High saw speeds up to 3000 RPM with tooth pitch of 5 to 10mm are used depending on sheet thickness. For circular saws, it is commonly recommended to use tooth geometry alternating between flat tooth, trapezoidal tooth and rigid metal. Always fasten the sheet and avoid vibrations during cutting to achieve clean cutting edges.
  • Drilling – PVC sheets can be drilled with conventional, high helix, high speed steel carbide tipped metal bits. Cutting edges must be kept sharp to prevent poor surface finish and undersized holes. Cutting and feeding speed depends on depth of bores, the thicker the sheet the lower the speed.
  • Routing – Stationary or hand routers can be used for slotting, beveling, rabbeting, rounding edges and trimming to the PVC boards. Best cutting results are obtained with carbide tipped router bits.
  • Milling – PVC sheets can be milled with milling tool that has allowance to accommodate smoother removal of chips. High forward feed along with moderate cutting speed and deep cuts will lead to good results.
  • Turning – PVC sheets can be worked by turning with a point of turning tool rounded to 0.50 mm radius to avoid linear marks on cutting surfaces. During precision turning, lower cut (2mm) and faster feeding should be used to prevent sheet breakage.
  • Cutting Punching – PVC sheets can be easily cut by shearing up to 3mm thickness. In case any deformity, rougher cut surface or fracturing is noticed, it is primarily because of sheet temperature. PVC sheet, a thermoplastic material, tends to acquire brittleness at lower temperatures. Therefore, pre-heat the sheet material to 95° – 131° F, before shearing. Die cutting by “Steel rule dies” is a common practice. Ideally it is 25mm wide strip steel, thickness 0.35–1mm, with one edge pre-shaped as knife. Bevel may be used depending on cut requirements with one side or both side honing. The bevel should be 5 or 6mm in length.
 
Yes! I am interested
Explore More Products
Get Best Quote
Get Best Quote
Get Best Quote
Get Best Quote
X
Looking for “PVC Boards”?
Find Us Rohit (Business Development Manager) No. 146, Sydenhams Road, Periamet Opposite Nehru Indoor Stadium, Gate No. 1, Chennai - 600003, Tamil Nadu, India
SEND SMS
SEND E-MAIL